In this short podcast episode, Bryan goes through the process of testing and replacing a run capacitor. Run capacitors provide continuous phase-shifted current to the start winding, allowing the motor to run in the right direction and with the appropriate amount of torque. These capacitors are needed in most of the single-phase PSC motors we work with. Run capacitors are in the circuit all the time and are connected in series with the start winding (compared to start capacitors, which need to be taken out of the circuit after startup). They don't actually "boost" voltage. The bigger the capacitor, the more current can move in and out of the start winding. Run capacitors are made of foil and oil (and the manufacturing quality usually correlates to the capacitor's lifespan), and they usually fail due to overvoltage or overheating. Capacitors may also be replaced with one of a higher voltage rating but not a lower one. Before you test a capacitor, perform a visual inspection. Bloated tops and oil leakage are signs of failure. You'll also want to measure the microfarads and make sure it's within range. An under load test occurs while the system is running (and should NOT be done on blower capacitors for safety reasons). Bench testing happens while the system is off and the capacitor is disconnected and discharged. We have calculators for testing on our app. To test under load, measure the amperage on the start wire and multiply it by 2652. Then, divide that number by the voltage to find the capacitance in microfarads. If the capacitance is over 10% low, replace the capacitor. When replacing a capacitor, make sure the system is off, the capacitor is discharged, and that you tighten the strap and wire it up correctly. It's also a good idea to bench test the new capacitor. "Capacitor Testing and Replacement Procedure" tech tip: https://www.hvacrschool.com/capacitor-testing-and-replacement-procedure/ "What Is Up With Blower Amps & Watts w/ Steve Rogers" podcast: https://www.hvacrschool.com/podcasts/what-is-up-with-blower-amps-watts-w-steve-rogers/ Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool. Purchase your tickets or learn more about the 7th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android
--------
17:54
Cold Coil vs. Desiccant Dehumidification
In this comprehensive episode of the HVAC podcast, Bryan hosts an in-depth discussion about dehumidification technologies with two industry experts: David Schurk, National Sales Manager for Innovative Air Technologies, and Nikki Krueger from Santa Fe Products. The conversation explores the fundamental differences between compression refrigeration dehumidification and solid desiccant systems, providing valuable insights for HVAC professionals dealing with moisture control challenges. David Schurk brings 44 years of industry experience and serves as an ASHRAE Life Member and Distinguished Lecturer, teaching humidity control professional development courses. His expertise focuses on solid desiccant dehumidification systems for industrial and heavy commercial applications. Nikki represents Santa Fe Products, pioneers of whole-house ventilating dehumidification technology since the mid-1990s, and discusses the growing residential and light commercial market demands driven by tighter building construction and stricter energy efficiency requirements. The discussion delves into the critical importance of understanding dewpoint versus relative humidity measurements, a fundamental concept that often confuses technicians in the field. The experts explain how the dew point remains consistent throughout a space while relative humidity can vary dramatically based on temperature differences between rooms, floors, and ceilings. This understanding is crucial for proper system design, troubleshooting, and customer education, especially as homeowners become increasingly aware of indoor air quality concerns. The conversation also addresses the intersection of building science and dehumidification technology, emphasizing that proper moisture control requires both well-designed building envelopes and appropriate mechanical systems. From residential applications dealing with tighter construction and mechanical ventilation requirements to industrial processes like lithium battery manufacturing requiring extremely low humidity levels, the experts highlight how different technologies serve specific market segments while sometimes overlapping in commercial applications. Key Topics Covered Fundamentals of moisture control Compression refrigeration dehumidification Solid desiccant technology Market applications and demand drivers Building envelope importance Measurement and troubleshooting Water activity levels and mold prevention Technology boundaries Energy considerations Installation challenges Learn more about Santa Fe's products at https://www.santa-fe-products.com/, and learn more about David's work at https://www.dehumidifiers.com/. Both David Schurk and Nikki Krueger are active on LinkedIn, too. Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool. Purchase your tickets or learn more about the 6th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android
--------
59:41
Learning Better - Short #246
In this short podcast episode, Bryan talks about learning styles and gives some tips for "learning better" and getting more out of continuing education opportunities. The first step to getting more out of educational opportunities is to know your learning style. There are three main styles: visual, kinesthetic (hands-on), and auditory. Most tradespeople will probably fall into the kinesthetic category, but not everybody is; you need to figure out if you're most comfortable working with your hands, listening to podcasts, watching videos, or reading. It's also a good idea to try the practical knowledge first and then study the theory. Most people can learn via all of these media, though, and preferences in learning styles aren't excuses not to seek knowledge via the other pathways. Some people also do better with different instructional styles. Instructors can be more or less structured and outgoing, and you may have a preference. Find instructors who explain concepts and conduct their classes or seminars in ways that you understand best. Teaching is also a great way to get a better understanding of a concept, as is incorporating hands-on opportunities and quizzes when you read, watch videos, or listen to podcasts. When you can teach and be taught in non-judgmental environments, you can get a lot more out of the learning experience. Comprehension comes before retention, so memorization is usually not going to be too helpful for HVAC education. Understanding should be the main focus, not memorizing facts or test answers, and that includes challenging your assumptions and finding hard problems to solve. You can also discover HVAC/R concepts in unexpected places, including scientific or lifestyle YouTube channels and podcasts. Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool. Purchase your tickets or learn more about the 6th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android
--------
14:27
Intro to The Sigma Capacitor
Sharon Goepferich from Cool Air Products joins the podcast to discuss cutting-edge capacitor technology and innovative HVAC solutions in an introduction to the Sigma capacitor. Sharon brings a decade of industry experience, having worked extensively with capacitors and HVAC components while traveling across the country to educate technicians and contractors. The conversation begins with a comprehensive breakdown of capacitor failures, addressing common misconceptions in the field. While manufacturing quality certainly plays a role in capacitor longevity, environmental factors like high temperatures and voltage disruptions—particularly common in markets like Florida with frequent lightning strikes—are primary contributors to failure. A crucial point emphasized is that failing capacitors typically cause compressor and motor failures, not the other way around. Many technicians incorrectly assume that a capacitor reading within tolerance is acceptable, but Bryan and Sharon clarify that even a degraded capacitor operating at reduced capacity can cause motors to run hotter and fail prematurely. This highlights the importance of proactive capacitor maintenance and replacement before complete failure occurs. The episode's centerpiece is the discussion of the innovative Sigma capacitor system, which Sharon describes as being "designed on an airplane over whiskey." This modular pod system addresses a longstanding challenge for HVAC technicians: the impossibility of stocking every capacitor size on their trucks. The Sigma capacitor uses a stackable approach where technicians build the exact capacitance they need in the field using standardized components. The system operates on a simple rule: build the higher values first (typically compressor capacitance on top), then stack the lower values (fan capacitance) underneath. This approach maximizes truck inventory efficiency while minimizing the number of SKUs contractors need to manage, representing a middle ground between carrying extensive individual capacitor inventory and using traditional universal capacitors. Cool Air Products extends beyond capacitors with their Combat P Trap system, an all-in-one condensate drain management solution that combines a shutoff valve, cleaning tab reservoir, and P-trap in a single unit. This product reflects the company's mission to solve everyday contractor problems in cost-effective ways. What makes Cool Air Products unique is their business model of helping industry insiders bring innovative ideas to market, providing support for patent processes, manufacturing connections, and funding. The Combat P Trap also demonstrates the company's commitment to giving back, as a portion of proceeds supports veterans—fitting since the product was designed by a veteran and serves an industry with significant veteran participation. Key Topics Covered Capacitor failure analysis Proper capacitor testing techniques Installation best practices Sigma capacitor system Inventory management strategies Combat P Trap system Distribution challenges Cool Air Products' business model Veteran support initiatives Future product developments Professional networking Learn more about Cool Air Products at https://www.coolairproducts.net/. Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool. Purchase your tickets or learn more about the 6th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android
--------
28:49
What's up with Refrigerant & System Regulations w/ Copeland
_*]:min-w-0 !gap-3.5"> In this insightful episode of the HVAC School podcast, host Bryan sits down with Jennifer Butsch, Director of Regulatory Affairs at Copeland, to discuss the rapidly evolving regulatory environment affecting the HVAC industry. With eight years of experience at Copeland and a background spanning codes, standards, and regulatory affairs, Jennifer provides a unique perspective on the challenges and opportunities facing contractors, technicians, and manufacturers in today's market. The conversation begins with an in-depth look at the EPA's Technology Transition Rule and the recent shift from R-410A to mildly flammable refrigerants like R-454B and R-32 as of January 1, 2025. Unlike previous refrigerant transitions that allowed for years of overlap, this transition was compressed into a much shorter timeframe due to building code requirements for the new mildly flammable refrigerants. While equipment delivery has gone relatively smoothly, the industry has faced significant challenges with refrigerant availability, particularly R-454B service gas. Jennifer discusses how OEMs have responded creatively, including pre-charging units with additional refrigerant and providing recovery cylinders as short-term solutions. The discussion also covers the ongoing debate about potentially returning to R-410A, which Jennifer argues wouldn't solve the current cost and availability challenges. She emphasizes that manufacturers have already invested heavily in transitioning their production lines and that rolling back would actually increase costs and timeline complications while moving in the wrong direction environmentally. The conversation touches on energy efficiency standards and the limitations of what can be changed under current legislation, noting that rolling back to pre-2023 efficiency levels would require Congressional action to revise the Energy Policy and Conservation Act. Jennifer and Bryan explore the complex world of tariffs and their impact on pricing stability, the potential defunding of Energy Star and what privatization might mean for the industry, and the challenges of regulatory fragmentation when federal oversight decreases and individual states create their own rules. The episode concludes with Jennifer's perspective on Copeland's philosophy of industry stewardship and practical advice for contractors on how to make their voices heard through trade associations and direct communication with legislators. Topics Covered: Technology Transition Rule - EPA refrigerant phase-down from R-410A to 454B and R-32 Refrigerant Availability Challenges - Current shortages in 454B service gas and industry solutions Mildly Flammable Refrigerants - Building code requirements and safety considerations R-410A Rollback Discussion - Why returning to previous refrigerants isn't a viable solution Energy Efficiency Standards - Legal limitations on rolling back efficiency requirements Tariff Impact - Effects on pricing stability and manufacturing decisions Energy Star Program - Potential defunding and privatization concerns Regulatory Fragmentation - Challenges when states create individual rules vs. federal standards Industry Stewardship - Copeland's approach to leadership and collaboration Contractor Advocacy - How to effectively engage with trade associations and legislators Manufacturing Investment Challenges - Impact of policy uncertainty on long-term planning Transition Timeline Management - Lessons learned and recommendations for future regulatory changes Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool. Purchase your tickets or learn more about the 6th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android
Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.
España